STONE HMI+BC1110 Bluetooth Transparent Transmission Mobile Phone Display Synchronously

8 minutes, 0 seconds Read

  System Overview

  STVC070WT-01 is a 7-inch color touch screen produced by Beijing STONE Technology Co., Ltd. The color smart display has a built-in 128M storage space and can communicate with the outside through RS485/RS232. The official also provides a dedicated development tool TOOL to accelerate the development process. In addition, this system uses the Bluetooth module BC1110. and a simple Android phone APP to realize data intercommunication between the phone and the screen.

  System Design


  STONE STVC070WT-01 is a smart display terminal with a Cortex-M4 processor and 128M storage space. Any visual material and interface switching logic can be written into the display terminal in advance. And it can communicate with the outside through the serial port. Here we write the interface elements and interface switching logic directly into STVC070WT-01, and then reserve a serial port command to communicate with the mobile phone APP through the Bluetooth module.

  Process Design

  The biggest feature of STVC070WT-01 is that it abstracts GUI development from the entire product development process, thereby isolating the GUI development process, reducing the complexity and coupling of the entire project, accelerating the project development progress, and reducing project uncertainty.


  As shown in the figure above, traditional display terminal GUI development will go through a process of GUI element code abstraction. This abstract process requires the use of GUI code libraries such as QT, EmWin, LVGL, etc. This process will couple the GUI module with other code modules. This increases the complexity and uncertainty of the project.

  However, the use of smart display terminal development will eliminate the code abstraction process of GUI elements. Developers can directly divide functions and switch logic on the original image according to the art design, and are self-contained, and can be executed and tested independently of other product modules. Reserve the external functional interface (serial communication) to be organically integrated with the entire product. Simplifies the GUI development process, improves the product development speed, and reduces the complexity and uncertainty of the project.

  STVC070WT-01 smart display Development

  STVC070WT-01 is a civilian-grade smart display terminal of STONE Tech. Just get the product, you can first check the equipment is in good condition (below-left picture), open the plastic film on the screen, you can clearly feel the screen’s penetrating luster.


  Use the official distribution power adapter board and adapter cable to connect to smart display STVC070WT-01 to connect to the 12V power supply, then the device will run a factory test program (Test Case). At this time, we might as well click “HW TEST” in the figure below to perform a hardware test.


  At this time, we click to enter “Bad Points & grayscale” to perform a dead pixel and grayscale test. At this time, the screen will enter a solid color and grayscale gradient display, click to switch, and exit.


  After confirming that there is no problem with the screen, we follow the following address to download the development tool TOOL and its tutorial from the STONE site.

  This program uses two variable storage spaces 0x1251 and 0x1253, which are respectively used to store the indicator light display on and off (corresponding data: 1 and 0) and whether the Bluetooth connection mark is displayed (corresponding data: 1 and 0). For the development details of TOOL, please refer to the above document, so I won’t repeat it here.

  After using STONE TOOL to complete the GUI interface design and development, we connect the computer to the STVC070WT-01 smart display through a USB cable and connect it. The screen will display the program download prompt message “After download, please plug out USB mini”.


  Click the download button in the left picture below to download our program to STVC070WT-01. After the download is successful, the following right picture is displayed.



  As shown in the figure below, click the switch button at the bottom right to change the brightness of the small light in the middle.


  BC1110 Bluetooth Development


  The CC2541 is a power-optimized true system-on-chip (SoC) solution for both Bluetooth low energy and proprietary 2.4-GHz applications. It enables robust network nodes to be built with low total bill-of-material costs. The CC2541 combines the excellent performance of a leading RF transceiver with an industry-standard enhanced 8051 MCU, in-system programmable flash memory, 8-KB RAM, and many other powerful supporting features and peripherals. The CC2541 is highly suited for systems where ultra low power consumption is required. This is specified by various operating modes. Short transition times between operating modes further enable low power consumption. The CC2541 is pin-compatible with the CC2540 in the 6-mm × 6-mm QFN40 package if the USB is not used on the CC2540 and the I2C/extra I/O is not used on the CC2541. Compared to the CC2540, the CC2541 provides lower RF current consumption. The CC2541 does not have the USB interface of the CC2540 and provides lower maximum output power in TX mode. The CC2541 also adds an HW I2C interface.



  2.4-GHz Bluetooth low energy Compliant and Proprietary RF System-on-Chip
Supports 250-kbps, 500-kbps, 1-Mbps, 2-Mbps Data Rates
Excellent Link Budget, Enabling Long-Range Applications Without External Front End
Programmable Output Power up to 0 dBm
Excellent Receiver Sensitivity (–94 dBm at 1 Mbps), Selectivity, and Blocking Performance
Suitable for Systems Targeting Compliance With Worldwide Radio Frequency Regulations: ETSI EN 300 328 and EN 300 440 Class 2 (Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan)


  Few External Components
Reference Design Provided
6-mm × 6-mm QFN-40 Package
Pin-Compatible With CC2540 (When Not Using USB or I2C)

  Low Power

  Active-Mode RX Down to: 17.9 mA
Active-Mode TX (0 dBm): 18.2 mA
Power Mode 1 (4-µs Wake-Up): 270 µA
Power Mode 2 (Sleep Timer On): 1 µA
Power Mode 3 (External Interrupts): 0.5 µA
Wide Supply-Voltage Range (2 V–3.6 V)

  TPS62730 Compatible Low Power in Active Mode

  RX Down to: 14.7 mA (3-V supply)
TX (0 dBm): 14.3 mA (3-V supply)
High-Performance and Low-Power 8051 Microcontroller Core With Code Prefetch
In-System-Programmable Flash, 128- or 256-KB
8-KB RAM With Retention in All Power Modes
Hardware Debug Support
Extensive Baseband Automation, Including Auto-Acknowledgment and Address Decoding
Retention of All Relevant Registers in All Power Modes


  Powerful Five-Channel DMA
General-Purpose Timers (One 16-Bit, Two 8-Bit)
IR Generation Circuitry
32-kHz Sleep Timer With Capture
Accurate Digital RSSI Support
Battery Monitor and Temperature Sensor
12-Bit ADC With Eight Channels and Configurable Resolution
AES Security Coprocessor
Two Powerful USARTs With Support for Several Serial Protocols
23 General-Purpose I/O Pins(21 × 4 mA, 2 × 20 mA)
I2C interface
2 I/O Pins Have LED Driving Capabilities
Watchdog Timer
Integrated High-Performance Comparator

  Development Tools

  CC2541 Evaluation Module Kit(CC2541EMK)
CC2541 Mini Development Kit (CC2541DK-MINI)
SmartRF™ Software
IAR Embedded Workbench™ Available


  Bluetooth v4.0 Compliant Protocol Stack for Single-Mode BLE Solution

Complete Power-Optimized Stack Including Controller and Host
GAP – Central, Peripheral, Observer, or Broadcaster (Including Combination Roles)
ATT / GATT – Client and Server
SMP – AES-128 Encryption and Decryption
Sample Applications and Profiles
Generic Applications for GAP Central and Peripheral Roles
Proximity, Accelerometer, Simple Keys, and Battery GATT Services
More Applications Supported in BLE Software Stack
Multiple Configuration Options
Single-Chip Configuration, Allowing Applications to Run on CC2541
Network Processor Interface for Applications Running on an External Microcontroller
BTool – Windows PC Application for Evaluation, Development, and Test


  2.4-GHz Bluetooth low energy Systems
Proprietary 2.4-GHz Systems
Human-Interface Devices (Keyboard, Mouse, Remote Control)
Sports and Leisure Equipment
Mobile Phone Accessories
Consumer Electronics

  CC2541 WITH TPS62730

  TPS62730 is a 2-MHz Step-Down Converter With Bypass Mode
Extends Battery Lifetime by up to 20%
Reduced Current in All Active Modes
30-nA Bypass Mode Current to Support Low Power Modes
RF Performance Unchanged
Small Package Allows for Small Solution Size
CC2541 Controllable


  BC1110 is a low-power Bluetooth transparent transmission module (BLE) launched by Fengxin Internet of Things. It uses the CC2541 Bluetooth chip of Texas Instruments (TI), which has the characteristics of low power consumption and strong anti-interference.

  It uses library BPS to communicate with STVC070WT-01 and set the BPS_CMD_SET to ‘T’.

  We use the Bluetooth transparent transmission module BC1110 of Fengxin Internet of Things, and modify its code to send the connection status data to STVC070WT-01 every 1 second. And lead out the DIN, DOUT, and GND of the adapter cable and connect them to TX, RX, and GND of BC1110.


  Note: When STONE smart display STVC070WT-01 leaves the factory, the J17 of the backplane pad is connected to facilitate computer serial communication, but this will cause communication failure with the Bluetooth module, and you need to make sure it is disconnected here.

  13-STONE-STVC070WT-01+BC1110-Bluetooth+transparent-transmission-mobile-phone-display-synchronously(16) 13-STONE-STVC070WT-01+BC1110-Bluetooth+transparent-transmission-mobile-phone-display-synchronously(17)

  APP Development

  After APP connects to Bluetooth, use STONEn’s official serial communication protocol to read and write data of 0x1251 and smart display STVC070WT-01 to display the light on and off simultaneously. Android’s source is listed as follows:

  For complete code and project documentation, please contact us:


  STONE STVC070WT-01+BC1110 Bluetooth transparent transmission mobile phone display synchronously Project Demo


  STONE smart display STVC070WT-01 uses powerful local CPU calculation and storage, STONE TOOL development, and uses a serial port to communicate with the outside world, which greatly facilitates its work with external devices and greatly accelerates the development of embedded GUI interfaces.

  Related posts:

  Raspberry PI Pico and STONE Display Dazzling Light Control System
STONE LCD Arduino Esp8266 Cooler
Tutorial: STONE HMI display for EV charging infrastructure project
Control WS2812B_RGB Lamp by STONE Display Module
Automotive Car LCD Screen Project Solutions
Raspberry Pi GUI using STONE HMI Touch Screen Display Module
Ultrasonic module test with STONE LCD module
Medical TFT Manufacturers -LCDS For Medical Devices
The Structure and Display Principle of High Brightness LCD
STONE STWI056WT-01 + Arduino + Physical Therapy Instrument

STONE HMI+BC1110 Bluetooth Transparent Transmission Mobile Phone Display Synchronously

Similar Posts